Linotype Hell Linotronic 330 LTC 330 with RIP 50
Article number: 11325
Listed in category: Prepress / Computer To Film / Imagesetter > Linotype Hell Linotronic 330 LTC 330 with RIP 50 from brakensiek.de
Linotype Brightly Linotronic 330 LTC 330
Non-new
Capstan Technology
beige
Resolution: In 3048 dpi
Format: 305 x endless
cleaned and tested
no cassettes
optionally with Harlequin RIP
Device type 4318951
Technical Data
Light source: 3mW helium neon gas laser
Exposure system:Rotating polygon mirror
Control:Via the LI 2 and LI 5 interfaces
Ports/interfaces:LI 2 interface, LI 5 interface, power input
Optional: Connection for on-line processor
Output format:
Horinzontal305 mm (12 inch or 72 Pica) maximum scanline length
Vertical:With take-up cassette: 30 m or 100 feet (Maximum length, if using a HeNe laser film of 0.1 mm or 4 mil thickness and 310 mm or 12.2 inch width. In greneral, the vertical format depends on the RIP and front-end system)
With on-line processor connected: variable lengths up to maximum 800 mm or 31.5 inch can be defined according to the instructions of the processor manufacturer.
Photomaterial:Red -sensitive high speed imagesetting materials with maximum sensitivity at 632 nm and high contrast. Materials: polyester-based HN-laser film, HN RC-paper, HN-direct plate-making materials (printing foils)
Photomaterial supply from: Roller material, emulsion inside; light-proof pagaging; wound core diameter 50.4 mm or 2 inches
Requred density:Minimum log D 3; follow the density recommendations of the photomaterial manufacturer and select the corresponding density value on the input panel of the laser imagesetter.
Material thickness: 0.10 mm to 0.19 mm or 4 mil to 7 mil
Material widths: 150 mm, 200 mm, 250 mm, 280 mm and 310 mm
5.9 inch, 7.9 inch, 9.8 inch, 11.0 inch, 12.2 inch
Spot size:20 µm or 0.8 mil
Adressability (Resolution):In vertical and horizontal direction
3387 dpi (1333 pixel/cm)*
2540 dpi (1000 pixel/cm)
2032 dpi (800 pixel/cm)
1693 dpi (666 pixel/cm)
1270 dpi (500 pixel/cm)
846 dpi (333 pixel/cm)
635 dpi (250 pixel/cm)
A PostScript RIP 4 or PostScript RIP 300 with software version 51.8 upwards is requred to achieve all above resolution steps. (The reosultion step marked with * can be used only in LI 2 asynchronous mode with a 16 MHz clock.)
Maximum recorder Speeds:
Speed cm/min.:9.7
Speed inch/min.: 3.8
Resolution dpi:3387
Resolution pixel/cm:1333
Speed cm/min.:17.3
Speed inch/min.: 6.8
Resolution dpi:2540
Resolution pixel/cm:1000
Speed cm/min.:27.1
Speed inch/min.: 10.7
Resolution dpi:2032
Resolution pixel/cm:800
Speed cm/min.:39.0
Speed inch/min.: 15.4
Resolution dpi:1693
Resolution pixel/cm:666
Speed cm/min.:34.7
Speed inch/min.: 13.7
Resolution dpi:1270
Resolution pixel/cm:500
Speed cm/min.:78.0
Speed inch/min.: 30.7
Resolution dpi:846
Resolution pixel/cm:333
Speed cm/min.:69.6
Speed inch/min.: 27.4
Resolution dpi:635
Resolution pixel/cm:250
Non-new
Capstan Technology
beige
Resolution: In 3048 dpi
Format: 305 x endless
cleaned and tested
no cassettes
optionally with Harlequin RIP
Device type 4318951
Technical Data
Light source: 3mW helium neon gas laser
Exposure system:Rotating polygon mirror
Control:Via the LI 2 and LI 5 interfaces
Ports/interfaces:LI 2 interface, LI 5 interface, power input
Optional: Connection for on-line processor
Output format:
Horinzontal305 mm (12 inch or 72 Pica) maximum scanline length
Vertical:With take-up cassette: 30 m or 100 feet (Maximum length, if using a HeNe laser film of 0.1 mm or 4 mil thickness and 310 mm or 12.2 inch width. In greneral, the vertical format depends on the RIP and front-end system)
With on-line processor connected: variable lengths up to maximum 800 mm or 31.5 inch can be defined according to the instructions of the processor manufacturer.
Photomaterial:Red -sensitive high speed imagesetting materials with maximum sensitivity at 632 nm and high contrast. Materials: polyester-based HN-laser film, HN RC-paper, HN-direct plate-making materials (printing foils)
Photomaterial supply from: Roller material, emulsion inside; light-proof pagaging; wound core diameter 50.4 mm or 2 inches
Requred density:Minimum log D 3; follow the density recommendations of the photomaterial manufacturer and select the corresponding density value on the input panel of the laser imagesetter.
Material thickness: 0.10 mm to 0.19 mm or 4 mil to 7 mil
Material widths: 150 mm, 200 mm, 250 mm, 280 mm and 310 mm
5.9 inch, 7.9 inch, 9.8 inch, 11.0 inch, 12.2 inch
Spot size:20 µm or 0.8 mil
Adressability (Resolution):In vertical and horizontal direction
3387 dpi (1333 pixel/cm)*
2540 dpi (1000 pixel/cm)
2032 dpi (800 pixel/cm)
1693 dpi (666 pixel/cm)
1270 dpi (500 pixel/cm)
846 dpi (333 pixel/cm)
635 dpi (250 pixel/cm)
A PostScript RIP 4 or PostScript RIP 300 with software version 51.8 upwards is requred to achieve all above resolution steps. (The reosultion step marked with * can be used only in LI 2 asynchronous mode with a 16 MHz clock.)
Maximum recorder Speeds:
Speed cm/min.:9.7
Speed inch/min.: 3.8
Resolution dpi:3387
Resolution pixel/cm:1333
Speed cm/min.:17.3
Speed inch/min.: 6.8
Resolution dpi:2540
Resolution pixel/cm:1000
Speed cm/min.:27.1
Speed inch/min.: 10.7
Resolution dpi:2032
Resolution pixel/cm:800
Speed cm/min.:39.0
Speed inch/min.: 15.4
Resolution dpi:1693
Resolution pixel/cm:666
Speed cm/min.:34.7
Speed inch/min.: 13.7
Resolution dpi:1270
Resolution pixel/cm:500
Speed cm/min.:78.0
Speed inch/min.: 30.7
Resolution dpi:846
Resolution pixel/cm:333
Speed cm/min.:69.6
Speed inch/min.: 27.4
Resolution dpi:635
Resolution pixel/cm:250
Contact:
Your contact person: Tim Brakensiek
gebrauchtprodukt
last update:
20.11.2012