Linotype-Hell Linotronic 560 + OLP Glunz und Jensen + Highwater Harlequin RIP V7.2
Article number: 35109
Listed in category: Prepress / Computer To Film / Imagesetter > Linotype-Hell Linotronic 560 + OLP Glunz und Jensen + Highwater Harlequin RIP V7.2 from brakensiek.de
Linotype-Hell Linotronic 560
The alternative to Screen Katana, screen 3050 or Heidelberg Hercules Avantra 30 or if no punch is needed and to get along with the material width.
Non-new
Specifications:
System Description: Precision laser recorder
Dimensions (W x H x D): 103 x 95.5 x 81.5 cm
Image area: 457.5 mm, 108 pica (exposure length depending on application)
Resolution: 167-1333 pixels / cm
Speed: 120.4 to 7.5 cm / min
NV parameters such as those necessary for operation with a Harlequin 7.2 RIP are:
To arrive at these values need to expand the Rec 1 card and put the bridge B3, and starting a special key combination. This should take only an experienced service technician.
Setting Li5
9600
8 bits
1 stop bit
No parity
RTS / CTS
Setting Li2
By Panel and Li5
Asynchronous
16/8
Menu ADUJST PARAMETERS:
PG_RES $ 1E 0000
PG_TFAK ($ 16F8)
OPTIC ($ 9D)
SOL ($ B7)
FLM_RES $ 140,000
FLM_TFAK ($ B7E)
Menu MACHINE PARAMETERS:
ECLOSZ 315000000
PG_RPM 3344
PG_MAX 4600
PG_MIN 1400
TC_RPM 1442
TC_GN 1800
SOL_T1 350
SOL_T2 550
IM_CUT 132 000
WP_RAM 8
NC_1 $ 0
SOFTWARE PARAMETERS Menu
EEPROM_BLOCK 0
V_ADV_CUT 220 000
V_ADV_OLP 150 000
V_OLP_MAX 800 000
V_OLP_MIN 200 000
V_TKUP 30000000
SW_YVAL 2000
SW_DELAY 0
POWER_Time 0
EN_REC_TIME $ FF
STP_MMZM $ 0
SS_MODE 0
NC_2 $ 0
Menu MACHINE-TYPE
Recorder R1
Set1 560
Resolution Set Menu
X_Res $ 78,000
OD_Res $ F0000
OP_RNG $ A
DS_RNG $ 6
Menu-Adjust hardware
Density 450
Res 1333 l / cm
Type of material for test run
F-Width = 456 mm
F-Thik 0.1
Machine test instructions:
Press Service
Switch on the machine
Press Enter 3 times
If no error is present then at the end
P00000/E00269 / # 710 / C
Duration: 15 minutes
We recommend any change to update the NV-RAM data, since the buffer Battterie on the motherboard of the machine is empty and then at some point, the parameters are gone. These values will only work with this machine. For other machines, the values must be adjusted may be very costly. This requires an oscilloscope my 2x 100 Mhz, about 2 days and plenty of rest and patience.
Note: The on / off switch disconnects the power supply is not 100%. So please pull the plug from the socket in the evening around the machine to protect against surges.
The alternative to Screen Katana, screen 3050 or Heidelberg Hercules Avantra 30 or if no punch is needed and to get along with the material width.
Non-new
Specifications:
System Description: Precision laser recorder
Dimensions (W x H x D): 103 x 95.5 x 81.5 cm
Image area: 457.5 mm, 108 pica (exposure length depending on application)
Resolution: 167-1333 pixels / cm
Speed: 120.4 to 7.5 cm / min
NV parameters such as those necessary for operation with a Harlequin 7.2 RIP are:
To arrive at these values need to expand the Rec 1 card and put the bridge B3, and starting a special key combination. This should take only an experienced service technician.
Setting Li5
9600
8 bits
1 stop bit
No parity
RTS / CTS
Setting Li2
By Panel and Li5
Asynchronous
16/8
Menu ADUJST PARAMETERS:
PG_RES $ 1E 0000
PG_TFAK ($ 16F8)
OPTIC ($ 9D)
SOL ($ B7)
FLM_RES $ 140,000
FLM_TFAK ($ B7E)
Menu MACHINE PARAMETERS:
ECLOSZ 315000000
PG_RPM 3344
PG_MAX 4600
PG_MIN 1400
TC_RPM 1442
TC_GN 1800
SOL_T1 350
SOL_T2 550
IM_CUT 132 000
WP_RAM 8
NC_1 $ 0
SOFTWARE PARAMETERS Menu
EEPROM_BLOCK 0
V_ADV_CUT 220 000
V_ADV_OLP 150 000
V_OLP_MAX 800 000
V_OLP_MIN 200 000
V_TKUP 30000000
SW_YVAL 2000
SW_DELAY 0
POWER_Time 0
EN_REC_TIME $ FF
STP_MMZM $ 0
SS_MODE 0
NC_2 $ 0
Menu MACHINE-TYPE
Recorder R1
Set1 560
Resolution Set Menu
X_Res $ 78,000
OD_Res $ F0000
OP_RNG $ A
DS_RNG $ 6
Menu-Adjust hardware
Density 450
Res 1333 l / cm
Type of material for test run
F-Width = 456 mm
F-Thik 0.1
Machine test instructions:
Press Service
Switch on the machine
Press Enter 3 times
If no error is present then at the end
P00000/E00269 / # 710 / C
Duration: 15 minutes
We recommend any change to update the NV-RAM data, since the buffer Battterie on the motherboard of the machine is empty and then at some point, the parameters are gone. These values will only work with this machine. For other machines, the values must be adjusted may be very costly. This requires an oscilloscope my 2x 100 Mhz, about 2 days and plenty of rest and patience.
Note: The on / off switch disconnects the power supply is not 100%. So please pull the plug from the socket in the evening around the machine to protect against surges.
Contact:
Your contact person: Tim Brakensiek
purchase list
last update:
21.11.2012